The Haier washing machine self-diagnosis system, when a malfunction is found, issues a malfunction code to the panel. In electronic models, the error is shown on the display or on the board, on the washers without a screen, the indicators will flash. Therefore, it’s easier for you to understand the causes of the problem, just understand the meaning of the code.
After reading the material, you will save time on diagnostics and learn: what does the error code mean, what should be done when it appears. And also how to fix it, or fix the damage yourself.
Error table: what do the codes in the Hyer washing machine mean?
Malfunction code | Decryption | Reasons for the appearance | Repairs |
Legend | Short circuit - short circuit. SM - washing machine. SMA - automatic washing machine. | ||
ERR1 (ERR1) | Program crash. | There is a problem with the sunroof lock device (UBL), the door lock is broken. | 1. Replacing UBL. 2. Installing a new lock. |
ERR2 (ERR2) | Error draining water SMA Hayer. | Timeout expired (drain time exceeds 4 minutes). Clogged drain system CM. | 1. Cleaning the drain hose and filter. 2. Checking and replacing the drain pump. 3. Check the pressure switch, install a new part. 4. Repair of contacts of the electronic unit. |
ERR3 (ERR3) | Error ERR3 reports problems with the temperature sensor. In SM Hayer, water is not heated. | The temperature sensor has failed. | Change of temperature sensor. |
ERR4 (ERR4) | Problems with heating. Water does not heat up to the set temperature. | Malfunction of the heating element (TENA). | The solution to the problem is to replace the heater. |
ERR5 (ERR5) | Problems with the collection of water in the Hayer washing machine. | 1. Low pressure. 2. The water tap has been shut off. 3. Clogged inlet filter. 4. Violation of the wiring between the control module and the pressure switch, pump. | 1. Check the pressure in the water supply. 2. Unscrew the tap. It may not be fully open or closed. 3. Rinse the filter mesh of the intake valve. 4. Replace defective contacts. |
ERR6 (ERR6) | If CM Hyer gives an ERR6 error, then there are problems with the control module. | Defective control board, broken contacts, wiring. | The control board is inspected for damage. It is necessary to tightly connect the connectors, isolate the defective areas. |
ERR7 (ERR7) | The electronic unit is defective. Warning, critical code! | The unit could fail due to short circuit, or from prolonged use of the machine in a humid room. | It is necessary to change the electronic unit. |
ERR8 (ERR8) | If the ERR8 code is lit on the screen, it means that there is a problem in the water intake system. | The water in the tank of the Haier washing machine is more than necessary for washing. 1. Faulty pressure switch (water level sensor). 2. Failure of the electronic controller. | 1. It is necessary to replace the level sensor. 2. Repair of the electronic control unit and its contacts. |
ERR9 (ERR9) | ERR9 code is displayed on the panel. Malfunction during water intake in SM Hayer. | The tank is full of water. 1. Damage to the water supply valve. 2. There is a problem with the control board. | 1. Check, change the intake valve. 2. Diagnostics and installation of a new electronic board. |
ERR10 (ERR10) | An error occurred while taking water. | Damage to the pressure switch is likely. | Search for a pressure switch problem. Installing a new part on a Hyer washing machine. |
ERR13 | Engine problem | The engine failed, there is no voltage on the windings. | Check the electric motor: brushes, winding. Repair or replacement depending on the nature of the breakdown. |
UNB | Uneven arrangement of things in the drum of a Hyer washing machine. Imbalance. | When washing things went astray, the balance was upset. | To remove the error, you need to stop SM Hayer and manually distribute the laundry. |
EUAR (EUAR) | Error in the electronic board. | Violation of circuits of the electronic unit. | 1. Check wiring for defects and damage, repair of defective areas. 2. Repair or replacement of the controller unit. |
NO SALT | Unsuitable detergent composition for SM Hayer. | There is no powder in the tank, or its composition is not suitable for washing. | 1. To clear the error, check the dispensing tray. 2. Add some washing powder. 3. Inspect the powder supply channels into the tank, clean. 4. Select a washing mode without detergent. |
Now you know what the trouble codes in the Hyer washing machine mean. You have the opportunity to diagnose the problem yourself and repair yourself.